How To Create Your Own AMAZING Industrial Pipe Lamp

Industrial Pipe Lamp

Have you seen the ‘industrial pipe lamps’, which seem to be one of the new trends?  They have a Steampunk look, don’t they?  Yes, they are so unique!  They also have a hefty price on them but how difficult would it be to make an industrial pipe lamp at home?  And at what cost?

 

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

While you and I may not be savvy with all the plumbing paraphernalia, here, Jon-Michael, who works at the local Ace Hardware store, has come up with an easy DIY project!  How cool is this?  Can you imagine the impression made when you turn the red handle on the gate valve and the light comes on?

Jon-Michael put this first one together as I took photos of the process.  Then, using the directions, I put together a second one, which will be on the wall in the game room. 

How To Create Your Own AMAZING Industrial Lamp -Industrial Pipe Lamp on MyHumbleHomeandGarden.com

 

This may look like a disparate group of items, but when assembled together in a particular way, the end result makes a real conversation piece!  

Note in this picture, this type of light socket was changed to the kind in the picture and the materials list below.  It will be safer for this project.   After roughing this up, we realized there was a possibility of the socket causing a potential short and we chose the safer light socket.

 

Create your own amazing industrial pipe lamp! 

Click here to grab your own copy of this Illustrated Step-by-Step Guide!

Amazing Industrial Pipe Lamp
Industrial Pipe Lamp – E-Book

For this Industrial Pipe Lamp project, you will need:

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

Parts List For Pipe Lamp
Parts List For Pipe Lamp

 

 

 

 

 

 

 

 

 

You Will Also Need :

Electrical tape, an adjustable wrench,  a plumber’s wrench or vice, and quick-setting epoxy.  You may need Teflon tape.

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

Spacers for mounting on the wall (This will give enough room for the cord to slip between the wall and the flange.) or you could mount the lamp on a board, plaque, or piece of a pallet.  You could create a channel in the back of the wood to accommodate the cord.

 

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

 

This multi-tool from Gerber really came in handy for this project.  These were a Christmas gift last year for my son and he uses them all the time!  (We are an Amazon affiliate and may receive a small percentage of any purchases through this link.  Thanks for supporting this website!)

 

The Lamp Cord we chose is an 8′ Silver cord.

Disclaimer – A word of caution here, work with a licensed electrician or a certified professional to help with wiring your lamp. We are not responsible for any action taken as a result of the information or advice on MyHumbleHomeandGarden.com.

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #PipeLampHowTo #PipeLamp

 

 Industrial Pipe Lamp Instructions

 

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

 

Thread the male end of a 90° Street Elbow into one end of the 1″ Tee.  (Each thread can be slightly different.  Not all the threading starts in the same spot.  If the elbow, once tightened, is not at the right angle, wrap with 2 – 3 turns of Teflon tape and retighten. )

 

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

 

Cut two pieces of the smaller vinyl tubing about 3″ long and slide one over each of the rotary switch wires, stopping about an inch from the switch.   The tubing helps prevent the plastic coating on the wire from being damaged on the abrasive interior of the pipes.  The plastic coating on the wire is to protect you from being electrocuted!  You don’t want to damage that wire!  

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

 

Insert the switch into the elbow and Tee fitting with one tube-covered wire extending from each end. 

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

 

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

 

Loosely thread the 1 – 1/4″ to 1″ Reducing Bushing into the 1-1/4″ coupling.

*Do not tighten at this time. 

 

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

 

Loosely thread the 1″ close nipple into the 1-1/4″ to 1″ reducing bushing from the previous step.  

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

 

Insert the socket, wire ends first, up through the 1-1/4″ coupling, and out the top of the 1″ nipple.

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

 

Connect the black wire from the light socket to the wire from the switch, using a wire nut(Remove the small piece of plastic insulation from the end of the switch wires and the socket wires first.)  Twist the ends of the wire slightly before covering it with the wire nut.  Then, twist the wire nut catching the wires inside.  There should be no bare wire showing once the wire nut has been tightened!  Be sure to wrap the wire and the wire nuts with electrical tape.  I have seen where some say this is not necessary but I prefer to err on the side of caution!

The correct way to wrap the wire with electrical tape is to pull the tape tight and start wrapping the wires going into the wire nut, wrap across the wire nut, wrap back to the middle, and then cut the tape.  I cut a piece of tape about 8″ long so it was more manageable.

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

Cut 1″ of the 1/4″ tubing and carefully press this onto the brass tip of the rotary switch.   Press down and then continue pressing back and forth when it becomes difficult.  It needs to completely cover the brass tip but not the threaded plastic piece.  (My first instinct was to heat the tubing but I was informed not to do this!  It distorts the plastic.  Slow, steady pressure, and wiggling back and forth slightly finally worked.)

 

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

Place the 1/2″ gate valve into a vice or hold it in place with a plumber’s wrench.  

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

Taking a second wrench, unscrew the stem from the valve and remove the brass tip from the end of the stem.

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

Mix a small amount of epoxy following the directions on the package.  

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

Place a small amount on the threads of the stem and thread this into the reducing bushing.  *Do not over-tighten!

Wipe off any excess and let dry for 10 minutes.  

 

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

 

 

 

 

 

 

 

Set the 1″ to 3/4″ reducing bushing and stem from the previous step in front of you.

Now, take the valve Stem – Bushing piece, press the other end of the tubing from the rotary switch onto the end of the stem firmly and thread the bushing into the top of the tee.  (If you are having difficulty pushing the tube over the end of the stem, and I did,  rock it back and forth slightly, while pressing the bottom of the rotary switch from inside the tee.)

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

To prepare the lamp cord, pull the two end wires of the cord apart for about eleven inches.

Cut an 8″ length of the 3/8″ tubing and insert the neutral wire all the way through the tubing.How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

Next, run the tubing with the wire inside, through the tee-elbow fitting.  (You might have to loosen the switch assembly to allow the tube with the wire to pass through.  Remember to tighten afterward!)

On the specific lamp cord used for our project, the ribbed wire is the Neutral.  The smooth wire on the cord we used is the HOT wire!  It also has the black wording on it. (Be sure to check the package for which wire is hot on the cord you use.) We wrapped a small piece of black electrical tape around the hot wire for easier identification.

 

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

 

Connect the two neutral wires with the wire nut, the neutral from the socket, and the neutral wire from the lamp cord.    Wrap with electrical tape like before. 

 

Now, connect the two hot wires, (the one from the lamp cord marked with the black electrical tape and the one from the switch), with the wire nut and wrap them with electrical tape.

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

 

Unscrew the close nipple and thread it into the street elbow, guiding the wires through the center as much as possible to keep the wires from being skinned. 

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

Next, unscrew the 1-1/4″ to 1″ Bushing and thread it onto the nipple from the previous step.

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

Gently press the wire nuts and wires back up into the reducing bushing and then thread the coupling onto the reducing bushing. 

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

*Do not twist the socket as you spin the coupling!

 

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

Finally, thread the 1-1/4″ Coupling onto the bushing.  (Note the socket is still loose and not seated in the bushing.)

Wrap the light socket, behind the raised rim 2-3 times with electrical tape. Then, take hold of the light socket, twist it counterclockwise 1/2 turn, and then press firmly into the 1-1/4″ bushing another 1/2 turn clockwise. 

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

Carefully insert the prong side of the cord into the remaining pipe nipple and guide the cord through.

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

*The prong on ours was snug, but it was able to be eased through the pipe.

Guide the rest of the cord through the pipe, keeping it away from the sharp pipe edges, and then thread the nipple into the tee. 

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

Guide the cord through the flange in this same manner and thread the flange onto the pipe nipple.

How To Create Your Own AMAZING Industrial Lamp on MyHumbleHomeandGarden.com

To mount this to the wall, you will need 4 drywall anchors (if not mounting into a stud) and 4 nylon spacers (these will allow the cord to hang down the wall without being pinched when mounted).

You could also use a wooden base of your choice for the lamp.  Just drill a 1/2″ hole through the wood to allow for the cord.  You might want to create a channel down the back for the cord, too.

We opted to buy and use one of the Edison light bulbs.  Don’t they look neat in this industrial pipe lamp?  When lit, they just look like regular light bulbs.

Create your own AMAZING industrial pipe lamp!  It’s really pretty easy!  Click here for a Pipe Fitting Cheatsheet – Everyday Pipe Lamp Essentials you need to know.

Industrial Pipe Lamps

How To Create Your Own AMAZING Industrial Lamp. #DIYPipeLamp #IndustrialPipeLamp #PipeLamp

 

Be Social!

Yes, join 45 k + followers on our Pinterest Boards, where we pin our favorite creative ideas and share our own!

Follow me on Instagram, Pinterest, and Facebook so you won’t miss anything!  I would love for you to share this post with your friends!  They need great ideas, too!  Pin it!  It only takes a second!  #pipelamp #pipe #lamp

 
 

 

MiloTree
MiloTree

27 comments / Add your comment below

  1. Nice project, but note that the rotary switch was not included in the parts list. Are there any specs for this switch?

    1. David,
      Thank you so much for calling this to my attention! Although it was in the picture, it was not labeled. I took care of that and added it to the parts list, too. If you are buying it from Ace, the Ace number is #3531787. It’s a 6 Amp, 125 Volt Single Pole Switch. Thanks, again!

  2. Hi. I’m also making a lamp like this, but I’ve a question about the switch.
    The switch is 125V, but how many Volts is the lamp itself?? Because a vintage led bulb is 220V. Is this a problem for this kind of switch? Thnx 4 your reply ….. Siegfried.

    1. Siegfried, The lamp itself is a 120V lamp. The vintage lightbulbs we used in our projects are 120V. If you use a 125V switch with a 220V bulb, it will not work and could be a fire hazard. Especially if your electrical wall outlet is 220V! What is the voltage of your wall outlet? In theUS, it is typically 120V, however, I realize many other countries use 220V, especially in Europe.

  3. Great skills and amazing works. thanks for sharing this is really helpful for me and also for my upcoming project. so i hope you to add some more in future

  4. I bought a 3/4 inch tee for the gate valve to screw into instead of buying a 3/4 inch bush but they don’t fit.Any ideas?

  5. I’m confused about the T portion of it/ T and brass switch. So the brass valve screws into the 1 1/4″ to 1″ reducer which then screws into the 1″ T? I’m just confused by this and could use a little clarification thanks. I would think the brass valve itself would be ~3/4 of an inch

    1. Bradley, Jon-Michael’s reply: It threads into the 1″ to 3/4″ reducer. Then screws into the 1″ tee. The threading on the valve stem is actually a special threading that doesn’t quite work with a standard pipe connection which is why we used epoxy to keep it in place. Only tighten this until it’s snug.
      Hope this clarifies it. Good luck with your lamp!

  6. Your parts list has D- 1″ coupling, but the instructions say to connect “1 – 1/4″ to 1″ Reducing Bushing into the 1-1/4″ coupling.” Am I missing a part or instruction someplace? Thanks, very good basics for the lamp.

    1. You are right, Jeffrey! The parts list should have read1-1/4″ coupling. Thanks for calling that to our attention. I will get that fixed. Hopefully, no one was stumped with that.
      Thanks, again!

  7. I really appreciate the detailed wiring instructions. I’ve never messed with electrical anything before, always leave it to my husband, but I want to make this for him as a Christmas gift. I think I can do it now, so thank you!

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Verified by MonsterInsights