Don’t you think a dried wheat bundle is beautiful in its simplicity? Yes, but a pretty ribbon bow with the addition of a beautiful wax seal takes it over the top. Right?
I’ve been planning to buy a wax seal set for a while now. The other day, several ideas for using the wax seals came to mind as I was brainstorming. Anxious to start creating, I ordered two sets.
Then, I saw that you can actually use a low-melt glue gun, too! So, I also ordered some wax melt sticks for a mini glue gun! It just so happens that I have an extra low-melt mini glue gun. It’s probably a good idea to have one specifically designated for the colored waxes. I’m planning some more projects with some more stamps I’ve bought.
Supplies Needed for This Project
- Wheat bundle
- Ribbon
- Sealing Wax Kit
- Alphabet Wax Seal Stamp
- Scissors
- Ziploc bag of ice
- Paper Towels
- Low Melt Glue Gun
- Metallic color pen
The Wheat Bundle
(We are an Amazon affiliate and may receive a small percentage of any sales through the links in this post at no cost to you. Thanks for supporting this website.)
HomeGoods has wheat bundles like these right now. That’s where I bought the two here. You might not be able to find these throughout the year, but they are usually available in stores in late summer and fall. You can find wheat bundles on Amazon all year long.
There were not two matching wheat bundles. The plan was to remove the ribbon and the twine and replace them with a pretty ribbon. Considering which ribbon to use, I remembered the black striped ribbon I used to make a ribbon wreath a couple of years ago. Perfect!
Striped Ribbon Wreath
DIY Striped Ribbon Wreath – Beautiful, Quick, and Easy
Decorate With Ribbon
Next, cover up the glue with the ribbon. You’ll want to wrap the bundle with the ribbon, tie an overhand knot, and then, make a pretty bow. You’ve seen a lot of these bundles with ribbons and bows. Normally, the ends are cut short. If you leave the ribbon ends longer, you can arrange them nicely on the table. They look a little richer, don’t they?
I love these simply adorned with the ribbon! But to add that extra pizazz, we are adding wax monogram stamps!
The Wax Stamp Seals
#1 – Chill the Stamp
First, you’ll want to place the stamp on ice. A cold stamp will help set the wax faster. Put ice cubes in a plastic bag. Place the bag in a shallow bowl or a plate. Then, set the stamp face down on the plastic bag. Place a paper towel next to the ice pack. You’ll want to dab the stamp on the paper towel to remove any condensation.
#2 – Melt The Wax
Next, you need to melt the wax. I chose this set because it includes a little warming stand to set over the tealight candle. The tea lights for this warming stand are not as tall as regular tea lights. Some of the other sets have a warmer with little legs and, to me, that seemed a little more apt to tip than this one. The set also includes a separate wooden spoon holder for holding the hot spoon.
It’s important to just melt the wax. You will want to keep a close eye on it. If the wax gets too hot, it will cause bubbles and won’t make a pretty seal. After the wax is completely melted, allow it to cool for a few seconds before pouring it.
#3 – Pour the Wax
Typically, you pour the wax in the middle of a bow on a package or an envelope and press the seal right on it. In this case, I am not taking a chance on messing up the ribbon and seal. So, for this project, the wax seal is created on parchment paper and then, I’ll dot a bit of wax or low-melt glue on the ribbon and place the seal.
To make a perfectly round seal, try to pour right in the center, without moving the spoon around.
After pouring the hot wax, some might drip down the side. Just use a paper towel to wipe it off. If the wax hardens, heat the spoon over the flame for a few seconds and then, wipe off the wax. After you have finished using the wax, just heat the spoon and easily wipe all the wax from the bowl.
#4 – Blot the Stamp and Press it into The Wax
There may be some condensation on the stamp. Be sure to blot the stamp on a paper towel. Then, press the stamp into the wax. The weight of the seal presses into the wax. You really don’t need to apply pressure.
Typically, if your stamp has a definite top and bottom, you should be sure to use a pencil to make a mark on the side of the brass stamp right above the top. Then, you’ll know to position the mark at the top when you press into the wax. If you use a marker for this, it may discolor the wax. Use a pencil.
In this case, it really doesn’t matter because the seal can be turned in any direction before I glue it to the bundles.
#5 – Remove the Stamp and Reveal
Slowly, start to remove the stamp. If the wax moves, stop and allow the wax to cool some more. If it feels stiff as you wiggle the handle, it’s ready. Gently wiggle and then, it will release.
If it doesn’t release, don’t freak! You will be surprised how easily it comes off the brass stamp. I thought it might attach to the parchment paper, too. I thought it might have to be peeled off, but no.
Don’t be intimidated by this. Let me tell you that it is pretty forgiving. Not happy with a few of the seals I made, I folded them up and put them back in the spoon! The wax melted and I tried again.
To make the monogram more visible, use a metallic color pen to add color to the raised areas.
Finish The Wheat Bundle with a Wax Seal
Squeeze a little low-melt glue onto the middle of the bow. Then, place the wax seal on top of the glue, centering the seal.
Here’s an up-close of the wax seal.
These look perfect in the Thanksgiving tablescape! I love them! Don’t they look classy? And they are so easy to create!
Be Social!
Yes, come join 40 k + followers on our Pinterest Boards, where we pin our favorite creative ideas and share ours!
Follow me on Instagram, Pinterest, Bloglovin’, and Facebook so you won’t miss anything! I would love for you to share this post with your friends! They need amazing ideas, too! Pin it! It only takes a second! #Thanksgiving #wheatbundle #waxseal #monogram